Brick and Mortar Calculator
Work out how many bricks, how many bags of mortar and how much sand your wall really needs — measured in square feet or meters. Left side: your inputs. Right side: the numbers — with opening deductions, waste factor, single or double wythe and a bond-pattern diagram drawn live.
Wall Dimensions
= 10′ (3.05 m)
= 8′ (2.44 m)
Each wall keeps its own unit (ft / in / yd or m / cm / mm). Doors, windows and vents are subtracted from the brick area automatically.
Running Bond · Modular (7 5/8" × 2 1/4" × 3 5/8") · first wall shown to scale
Bricks (net)
549
theory, no waste
Order (waste 10%)
604
recommended purchase
Mortar (80 lb)
17
3/8" joint · single wythe
Wall Area
Mortar & Weight
Industry-grade defaults: the 3/8" mortar joint, one cement bag per 142 modular bricks and the 10% waste rule are pre-loaded — the same conventions masonry estimators use, with every value editable in the Advanced panel.
⚡Quick answers people search for most
Common walls computed with the same engine that powers the tool above — open the calculator and swap in your own numbers.
🧱
10 × 8 ft wall · Modular brick
549 bricks
The textbook example: 7 modular bricks per square foot. Mortar at a 3/8" joint, no waste.
🚪
10 × 8 ft wall · 3 ft × 6.8 ft door
409 bricks
The door eats 20.4 ft² of wall — the calculator subtracts it before counting, so you never buy bricks for air.
🧱🧱
Same wall, double wythe
1097 bricks
A solid two-wythe wall doubles the count — plus collar-joint mortar between the layers.
📦
Four 20 × 8 ft courtyard walls
4,828 to order
One run, four walls, 10% waste — 6,404 bricks with no pencil arithmetic between runs.
🪣
Mortar for 549 modular bricks
4 bags cement
Site-mixed 1:3 mortar: about 4 bags of cement plus roughly half a cubic yard of sand at a 3/8" joint.
🧺
Premixed 80 lb bags, same wall
17 bags
604 ordered bricks ÷ ~36 bricks per 80 lb bag — the joint-aware volume comes out near 17 bags.
🧮How to calculate how many bricks you need
Three steps, one formula each — the bricks calculation formula in feet, with every figure below reproduced live by the calculator. No black boxes.
Step 1 — Find the square footage of the wall in feet
Multiply the wall's width by its height. A 10 ft wide, 8 ft high wall is 80 ft². If you measured in inches, divide square inches by 144 to get square feet; in metric, meters × meters gives square meters directly. For walls with doors or windows, subtract each opening's area before moving on — the calculator's opening rows do this automatically and show the gross, deducted and net areas side by side.
wall area = width × height
net area = wall area − Σ(opening width × height × qty)
Step 2 — Find the area of one brick (with its joint)
A brick never sits alone: it occupies a cell of (length + joint) × (height + joint). For the modular brick at a 3/8" joint: 7 5/8" + 3/8" = 8" long and 2 1/4" + 3/8" = 2 5/8" high, so each cell covers 8 × 2.625 ÷ 144 = 0.1458 ft² — which is exactly where the "7 bricks per square foot" rule comes from (1 ÷ 0.1458 = 6.86).
brick cell = (L + j) × (H + j) ÷ 144 ft²
modular, 3/8" joint: (8 × 2.625) ÷ 144 = 0.1458 ft²
Step 3 — Divide, then add waste
Divide the net wall area by the brick cell area — the whole bricks calculation formula in feet is a single division: 80 ÷ 0.1458 = 549 bricks for the example wall. Then multiply by your waste factor — 10% is the working standard for running bond — and round up to a whole brick: 604 to order. For a double-wythe wall the whole count doubles before waste is applied.
bricks = net area ÷ brick cell × wythes
order = ⌈bricks × (1 + waste%)⌉
Why the calculator may differ slightly from the rule of thumb. "7 bricks per square foot" is a rounded convention. The engine uses the exact cell geometry, counts partial bricks at wall edges, and applies waste before rounding up — so 549, not 560, is the honest count for an 80 ft² wall. Trust the exact figure when ordering: on a 4,000-brick job the rounded rule quietly adds three cubes you may not need.
📐Mortar math, exactly as computed
Mortar scales with the joint thickness, not just the brick count — widen the joint and bags rise as bricks fall.
Mortar volume per brick (cell method)
mortar/brick = [(L + j)(H + j) − L·H] × depth
modular, 3/8": (21 − 17.16) × 3.625 ≈ 13.9 in³
Each brick's cell minus the brick itself is exactly the bed joint plus the head joint it consumes. Multiply the order quantity by that volume (plus collar-joint mortar between wythes) and you get the mortar the wall actually needs — which is why the bag count moves when you change the joint from 3/8" to 1/2".
From volume to bags
cement bags = volume ÷ 1.145 ft³ (1 bag ≈ 142 modular bricks)
sand (1:3) = cement bags ÷ 7 yd³
premixed = volume ÷ bag yield (80 lb ≈ 36 bricks)
The constants reproduce the published rules: one bag of cement lays 142 modular bricks at a 3/8" joint, a 1:3 mix takes one cubic yard of sand per seven bags, and an 80 lb premixed bag yields 30–36 bricks. Pick 1:4 or 1:5 and only the sand scales; pick a 60 lb bag and the premixed count rescales automatically.
Sand weight for delivery planning: dry sand runs about 2,700 lb per cubic yard. A 550-brick wall in a 1:3 mix needs roughly half a cubic yard — about 1,500 lb — which is why most masons have it dropped beside the pallet, not carried to it.
📏Brick coverage table
Sizes and coverage rates of the most common US brick styles — the same presets the calculator ships with. Switch to metric and the table logic holds in mm.
| Brick style | Size (L × H × D) | Metric | Weight | Bricks / ft² | Bricks / m² |
|---|---|---|---|---|---|
| Modular | 7 5/8" × 2 1/4" × 3 5/8" | 194 × 57 × 92 mm | 4.2 lbs / 1.9 kg | 7 | 73 |
| Queen | 7 5/8" × 2 3/4" × 3 1/8" | 194 × 70 × 79 mm | 4.1 lbs / 1.86 kg | 6 | 73 |
| Closure | 7 5/8" × 3 5/8" × 3 5/8" | 194 × 92 × 92 mm | 6.8 lbs / 3.1 kg | 4.5 | 48 |
| Standard | 8" × 2 1/4" × 3 5/8" | 203 × 57 × 92 mm | 4.5 lbs / 2 kg | 6.5 | 70 |
| Jumbo Standard | 8" × 2 3/4" × 3 5/8" | 203 × 70 × 92 mm | 5.9 lbs / 2.7 kg | 6 | 61 |
| King | 9 5/8" × 2 5/8" × 2 3/4" | 244 × 67 × 70 mm | 5.6 lbs / 2.5 kg | 4.5 | 49 |
| Roman | 11 5/8" × 1 5/8" × 3 5/8" | 295 × 41 × 92 mm | 4.7 lbs / 2.1 kg | 6 | 64 |
| Norman | 11 5/8" × 2 1/4" × 3 5/8" | 295 × 57 × 92 mm | 6.4 lbs / 2.9 kg | 4.5 | 49 |
| Utility | 11 5/8" × 3 5/8" × 3 5/8" | 295 × 92 × 92 mm | 10.2 lbs / 4.6 kg | 3 | 32 |
Coverage assumes a 3/8" mortar joint. Many bricks have three or more core holes to cut weight and cost; veneers are thinner again. The Custom Size option reproduces this table for any brick on earth — enter length, height and depth and the per-ft² figure updates with your joint, not the table's assumption.
🧱Bond patterns and what they cost you in waste
The pattern changes both the look and the cut count. Pick one in the calculator and the diagram redraws while the suggested waste updates.
Running Bond
10% wasteStretchers offset by half a brick. The default for structural and veneer walls because the lap locks the courses together. Cuts happen at openings and corners — 10% waste is the working norm.
Stack Bond
10% wasteEvery head joint aligned in a vertical line. Contemporary look, but the aligned joints concentrate movement and demand good control joints. Cutting is minimal, so waste stays near 10%.
English Bond
13% wasteAlternating full courses of stretchers and headers. Headers tie double-wythe walls together — classic for solid brickwork. Header courses double the cut count at edges, so plan ~13% waste.
Flemish Bond
15% wasteStretchers and headers alternate within each course, producing the decorative checker face. Every second brick is a header, so cutting loss is the highest of the four — the calculator suggests 15%.
🧑🏭Field tips & buying rules the formulas won't tell you
The details that decide whether the estimate survives contact with a real site — learned the hard way, worth reading before you order.
Buy the whole job from one batch
Clay bricks vary slightly in color and size between production batches — sometimes visibly. Ordering the shortfall later from a different dye lot is how walls end up with patchwork corners, and popular colors do go out of production. Order everything from one batch and keep a few unopened cubes spare: future repairs in matching brick are worth more than the storage space they cost.
Corners, terminations and lintels eat the waste factor
Every opening adds four cut corners; every wall end needs closers or half-bats; soldier and header courses multiply the cuts again. A straight 30 ft run can hold its 10%, but the same wall with two windows and a return wall will not — that is why patterned bonds carry 13–15%. When in doubt, round the waste up, not down: unused bricks stack, missing bricks stop the job.
Wet the bricks, watch the weather
Hot, dry or windy conditions pull water out of mortar before it cures, leaving weak, crumbly joints — high-suction clay bricks should be wetted (then allowed to surface-dry) before laying. In freezing weather the mixing water itself can freeze and destroy the bond, which is why masons protect fresh work below ~40°F. The calculator counts materials; site conditions decide whether they perform.
Material estimates are not the whole quote
Bricks, mortar and sand are the lines this tool prices. Labor, scaffolding, wall ties, flashing and weep holes, lintels over openings and waste disposal are separate items in every real quote — and on veneer work the ties and flashing are not optional extras, they are the part that keeps the wall attached and dry. Compare contractor bids line by line, not by total alone.
The 5% that saves a wall: even with a correct waste factor, keep roughly one extra cube (≈500 bricks) from the same batch for future repairs — patching with mismatched brick decades later is the most visible estimating failure there is.
📝How to use the brick calculator
Four steps from a tape measure to an order sheet your supplier can quote against — the interface labels the rest.
Enter the walls and their openings
Type each wall's length and height — one row per wall, named so the breakdown stays readable — and add every door, window and vent with width, height and quantity. The gross, deducted and net areas update as you type, and that net area drives every number downstream.
Pick the brick and the wall thickness
Choose one of nine presets (exact dimensions shown) or pick Custom Size and enter length, height and depth in inches or millimeters. Then set the wythe: single for veneer, double for solid walls — the count and the collar-joint mortar follow instantly.
Set the joint, waste and mortar format
Keep the 3/8" joint or widen it; pick a waste factor (bond-pattern suggestions applied automatically) and choose premixed bags or site-mixed cement + sand at your mix ratio. Mortar rescales with the joint in both modes.
Read the results and order in whole cubes
The right panel reports net bricks, the waste-adjusted order quantity, mortar bags, sand and — with prices typed in — a cost total that sums its lines exactly. Round the order up to whole cubes of ~500–526 bricks and keep the spare stock for future repairs in the same dye lot.
🧪Worked example: a 10 × 8 ft veneer wall with a door
Every number below comes from the same transparent math the calculator runs — the classic 80 ft² wall, minus a 3 ft × 6.8 ft door.
The math, step by step
- Gross wall area: 10 × 8 = 80 ft².
- Door deduction: 3 × 6.8 = 20.4 ft²; net area = 80 − 20.4 = 59.6 ft².
- Brick cell (modular + 3/8" joint): 8" × 2.625" = 0.1458 ft² → 6.86 bricks per ft².
- Net bricks: 59.6 × 6.86 = 409 bricks.
- Waste 10%: 409 × 1.1 = 449.9 → 450 to order — one and a bit cubes short of a pallet, so round the delivery to 2 cubes if the supplier insists.
- Mortar: 450 × 13.9 in³ ≈ 3.6 ft³ → site-mixed 4 bags of cement + 0.5 yd³ sand (1:3), or about 13 premixed 80 lb bags.
- Weight: 450 × 4.2 lb ≈ 1,890 lb — one pickup-truck-rated load, or half a cube on a flatbed.
Calculator output for this example
Net bricks
409
door deducted
Order (10% waste)
450
rounded up
Net brick area
59.6 ft²
80 − 20.4
Cement (1:3)
4 bags
+ ~0.4 yd³ sand
Premixed 80 lb
13 bags
joint-aware
Brick weight
≈ 0.9 tons
1,890 lb
📊Common project benchmarks
Typical small projects computed with the same engine at a 3/8" joint and 10% waste — a quick sense of scale before you measure anything. Your numbers will vary with brick size, openings and bond.
🌿
Garden border / low bed wall
12 ft × 1½ ft · single wythe · modular · 10% waste
🏡
Backyard privacy wall (4 sides)
4 × (24 ft × 6 ft) · one 4 ft gate opening · 10% waste
🚗
Garage / shed facade veneer
22 ft × 8 ft · 9×7 ft door · single wythe · 10% waste
Reading the benchmarks: the privacy-wall figure is four walls in one run with a gate deducted — the kind of result the multi-wall workflow produces directly. Sand for site-mixed mortar runs about 1 yd³ per 7 cement bags at 1:3; add roughly 13 premixed 80 lb bags per 500 ordered bricks as a field cross-check.
🎓About the Methodology & Expert Review
How the numbers on this site are produced, checked and kept honest.
Calculations on this site follow the conventions published for ASTM C216 facing brick and the standard US modular size system, including the 3/8" mortar joint assumption behind every published bricks-per-square-foot figure and the modular coordination that makes 8" × 2 5/8" cells tile a wall without cuts.
Mortar quantities are calibrated to the masonry industry's estimating rules — one bag of cement per 142 modular bricks, one cubic yard of sand per seven bags at a 1:3 mix, and 80 lb premixed bags yielding 30–36 bricks — then made joint-aware through the cell-volume method so the numbers stay correct at any joint width. Designed for homeowners, masons and general contractors, the tool is reviewed whenever brick standards, bag yields or coverage conventions change.
Standards-checked output
Presets match published US brick dimensions in inches and millimeters; coverage reproduces the industry table at a 3/8" joint.
Conservative by design
Order quantities include waste and round up to whole bricks — the number you can buy against, not a best case.
Closed arithmetic
Cost totals are the exact sum of their lines; area deductions are shown gross → net so every step can be audited by hand.
Transparent formulas
Every result can be reproduced from the formulas published on this page — no hidden multipliers.
🔁Review & maintenance
Brick dimensions, coverage constants, mortar bag yields and mix-ratio rules are checked against published references whenever the referenced standards or packaging change — and reader corrections are verified and folded into the engine within the week, by the same people who maintain the calculators. The formulas and the prose are one body of work, updated together.
🎯Scope of use
These estimates serve planning and purchasing for small-to-medium brickwork: garden walls, veneers, facades, outbuildings. They are not a structural design tool. For load-bearing, multi-storey, below-grade or seismic work, quantities must come from a structural engineer or stamped construction drawings — and every order should be verified against your supplier's quotes and site conditions before purchase.
🤝Accountability
Who we are and how the site runs: About · report an error or submit a correction: Contact · limits of liability: Disclaimer · data handling: Privacy Policy.
❓Frequently Asked Questions
The brick-estimating questions we get most often — answered with the same formulas the calculator runs.